Striker™ (1.5 – 6.0 cu yd) Accessories

Striker 6" SIDE EXTENSIONS

6" SIDE EXTENSIONS

Hold more material in your Striker stainless steel hopper spreader with these 6″ extension kits. Each kit contains the brackets needed to add up to one additional yard of capacity depending on the hopper size (wooden boards not included).

Part Number

#99488
For All Models
CENTRAL POINT GREASE KIT

CENTRAL POINT GREASE KIT

The Central Point Grease Kit provides easy access to grease points, simplifying preventative maintenance greasing that is essential to maximize bearing life.

Part Number

#11763
For All Models
SPILL GUARD KIT

SPILL GUARD KIT

Available in 50″ and 70″ widths to cover the full range of Striker™ hopper spreaders, the Spill Guard Kit provides the loader with an improved line of sight to the hopper edges, while preventing material from overflowing into the bed of the truck from off-center loading. Spill Guards not compatible with 6” Side Extensions or Poly Lid Kit.

Part Number

#81119
70" Kit
#81120
50" Kit
WESTERN Parts and Accessories Logo

CHUTE EXTENSION KITS

The stainless steel Chute Extension Kit is intended for tall vehicle applications where a longer chute is required to maintain the proper spinner height. This allows the Striker to spread material at the width and pattern it was designed for.

*Standard for the 3.0, 4.5 & 6.0 cu yd Models.

Part Number

#99139
For the 1.5 & 2.0 cu yd Models
WESTERN Parts and Accessories Logo

4' EXTENSION HARNESS (CAB CONTROL)

The 4′ Extension Harness is intended for long, extended bed applications where a longer harness is needed to hook up to the cab control.

Part Number

#68508
7 Pin for Gas Models
#66460
11 Pin for Gas Models
WESTERN Parts and Accessories Logo

4' EXTENSION HARNESS (POWER/BATTERY)

The 4′ Extension Harness is intended for long, extended bed applications where a longer harness is needed for the power/battery.

Part Number

#68523
2 Pin for Gas Models
LED WORK LIGHT KIT

LED WORK LIGHT KIT

See more to do more with the Work Light Kit for better visibility at the rear of your spreader at night. Encased in anodized aluminum, and good to less than minus 20 degrees, this LED work light will put over 1000 lumens where you need them, when you need them. The LEDs mean low amp draw, so you can easily use more than one (see our Additional Work Light Kit, PN 99732-1).

Part Number

#99505-1
For All Models
LED WORK LIGHT KIT

ADDITIONAL WORK LIGHT KIT

Add more lights to your spreader. Easily and conveniently add one, two, or even more lights with this kit. Each additional light puts another 1,000 lumens at your command and is easy to integrate with your original Work Light Kit (see PN 99505-1).

Part Number

#99732-1
For All Models
LED STROBE LIGHT KIT

LED STROBE LIGHT KIT

Make sure you’re seen, day or night, with our Strobe Lights for added visibility during operation. Encased in high impact plastic, this yellow LED strobe works in temperatures as cold as -20°F and will ensure that you’re seen in all but the worst of conditions. Make sure you spread safely with strobe light markers.

Part Number

#99494
For All Models
POLY LID KIT

POLY LID KIT

Shields de-icing material from the elements, locks out moisture to prevent material bridging and protects against material overflow while loading. Not compatible with side extension accessory.

Part Number

#72750
Regular Capacity (1.5, 2 & 3 cu yd)
#72770
High Capacity (Both 4.5 & 6.0 cu yd)
WESTERN Parts and Accessories Logo

HYDRAULIC CONTROL VALVES

The Hydraulic Control Valve allows for independent dual-flow control of the spinner and drive motor compared to the standard on/off control.

Part Number

#95245
For All Hydraulic Models
MASTER ACCESSORY HARNESS

MASTER ACCESSORY HARNESS

For all gas and hydraulic Striker hopper spreaders, the first accessory requires its respective Master Harness Accessory, each subsequent accessory will hook into this harness. Integrate all your accessories with this convenient kit. Includes all the wiring needed to go from cab to spreader, an in-cab control panel, and rear of hopper storage for accessory fuses and relays, allowing total integration of our plug ‘n’ play accessories.

Hydraulic model master accessory harness kit shown.

Part Number

#99629
For All Gas Models
#99627
For All Hydraulic Models
VIBRATOR KIT

VIBRATOR KIT

Loosen up with this Vibrator Kit to help move stubborn material and prevent bridging. Featuring a 200V DC vibrator motor in a metal housing, our vibrator will help prevent bridging and clogging, improving material flow so you can do your job faster and better.

Only compatible with one 50 gal pre-wet tank kit or one 100 gal pre-wet tank kit.

Part Number

#76668
For All Models
VEHICLE-SIDE HARNESS KIT

VEHICLE-SIDE HARNESS KIT

The Vehicle-Side Harness Kit contains components to replace harnessing on the truck or wire a second truck to operate the spreader.

Part Number

#78402
For All Models
CHAIN TIE-DOWN KIT

CHAIN TIE-DOWN KIT

Chain Tie-Down Kit for additional in-bed stability and security. 72″ of high strength steel chain and binder allow you to add an extra measure of safety as you move tons of salt down the road. (Hoppers require bolting to the truck frame for proper operator safety.)

Part Number

#99690
For All Models
LICENSE PLATE KIT

LICENSE PLATE KIT

Stay street legal with this illuminated License Plate Kit for your alternate license plate location. Providing convenient mount methods and lighting in a high impact plastic casing, the license plate kit allows you to move your license to a spot that is visible and legally compliant. Don’t leave without it.

Part Number

#99686
For All Models
Spreader Control Plate

SPREADER CONTROL ADAPTER PLATE

Gain the flexibility and easy installation benefits of the cup holder control mount with every spreader installation using the new Spreader Control Adapter Plate Kit. Kit contains a durable metal mounting plate and hardware.

Control Cup Holder Mount not included, order separately (#82007).

Part Number

#82018
For All Models
Control Cup holder Mount

CONTROL CUP HOLDER MOUNT

Put a hard stop to juggling controls and cell phones. Functional and practical, the Control Cup Holder Mount lets you secure your WESTERN spreader controls or your smartphone (not included) on a flexible gooseneck mount for optimal, customizable positioning. This compact, easy-to-install genuine WESTERN accessory is designed to fit firmly into most size cup holders in your vehicle (image featuring plow control).

Now compatible with spreader controls using a Spreader Control Adapter Plate, order separately (#82018).

Part Number

#82007
For All Models
DIELECTRIC GREASE

DIELECTRIC GREASE

Don’t risk corrosion problems—use WESTERN® dielectric grease! Western Products recommends all owners consistently use our special formulation dielectric grease to protect all electrical connections in tough winter snow, ice and salt conditions.

 

Part Number

#49326
2 oz. Tube
EXTREME DEFENSE™ GREASE product image

EXTREME DEFENSE™ GREASE

Protect and maintain moving components within snow and ice equipment including bearings, hinges and pivot bolts with EXTREME DEFENSE™ Grease. WESTERN’s specially designed blend is optimized for the cold, wet and dirty environment common to snow and ice management. Custom formula maintains viscosity from -40 up to 300 degrees, and military-grade, corrosion-prevention additives protect equipment investments for the long haul with no harmful environmental side effects. EXTREME DEFENSE Grease is available in cartridges, pails, totes and drums.

Part Number

#72909
14 oz. Cartridge
#72910
7 lb Pail
#72911
120 lb Tote
#72912
400 lb Drum